This small trinket box is made from yellow heart, purple heart and some punky wood for the fretwork decorations that I wish I had thrown away.
Every once in a while you will come across some wood that is what I call punky. I can't define "punky" but I know it when I see it. I kind of looks okay when you cut it. It looks a little worse when you sand it and it looks like crap when you put a finish on it.
Oh well, not every project works out as well as we hope. If you decide to make this Victorian design trinket box I suggest you use 1/8" thick wood for the fretwork decoration. I not only used punky wood I used 1/4" thick and that is too thick.
When you are cutting the body of these scroll saw boxes you want to use a larger blade so the kerf is wide enough to allow the wall to slide back together, You will see in the pattern that the body is cut from a single block of wood. The interior waste is cut away. Then the inner wall is cut free and finally the outer wall is cut.
The the kerf is too small you will have a difficult time getting the box lid to slide over the inner walls. If you don't have a good fit, sanding will fix the issue.
Guest Post: Allen Pogach
I received an email from Allen a week ago telling me about his trouble changing scroll saw blades. It would take 10 to 12 minutes for him to change a blade on his DeWalt scroll saw. You see Allen suffers from an auto-immune muscle condition called "sporadic Inclusion Body Myositis (sIBM). This robs him of his fine motor skills.
Allen had come across a video I did showing the blade removal tool I made. The tool was to help people with weak or sore hands to release/tighten the thumb screw on the DeWalt style thumb screws.
He explained to me that the lower thumb screw was especially difficult. Then he showed me some modifications he made to the tool that has allowed him to change lower blade mush easier. This minimizes the frustrations and makes his time at the saw more enjoyable.
Allen was kind enough to send me pictures of his mods to the tool. He wanted to share with anyone who might have similar issues.
Thanks Allen, I bet there are a few people who will appreciate the time you put in to this.
Steve:
As I mentioned in my previous e-mail, I pretty much followed your video step by step.
1. Had to vary on cutting the pattern since (at the time) I could not tighten my 788 blade enough to cut;
2. Cut pattern on band saw with 1/8 inch blade 15 tpi;
3. I used pine instead of oak (not sure if that would cause a problem) but the dowel was 1.25 inches;
4. I cut the initial length of the "tool" to 8.25 inches. By luck the 8.25 inches turned out to be perfect;
5. Before I glued on the "tool" top, I found scrap 3/8 in dowel. I started drilling a hole
(approximately 2.5 inches fro the bottom) with a 1/16 bit. I slowly increased bit size to 3/8;
6. I believe the 3/8 dowel is 4 inches long (arbitrary length) with rounded edges;
7. I have yet to glue the 3/8 to the 1.25 dowel--it is snug enough for the time being;
8. If some wants precise measurements--let me know & I'll send them.
Allen
As I mentioned in my previous e-mail, I pretty much followed your video step by step.
1. Had to vary on cutting the pattern since (at the time) I could not tighten my 788 blade enough to cut;
2. Cut pattern on band saw with 1/8 inch blade 15 tpi;
3. I used pine instead of oak (not sure if that would cause a problem) but the dowel was 1.25 inches;
4. I cut the initial length of the "tool" to 8.25 inches. By luck the 8.25 inches turned out to be perfect;
5. Before I glued on the "tool" top, I found scrap 3/8 in dowel. I started drilling a hole
(approximately 2.5 inches fro the bottom) with a 1/16 bit. I slowly increased bit size to 3/8;
6. I believe the 3/8 dowel is 4 inches long (arbitrary length) with rounded edges;
7. I have yet to glue the 3/8 to the 1.25 dowel--it is snug enough for the time being;
8. If some wants precise measurements--let me know & I'll send them.
Allen
The tool is currently locked on to the blade tightener (sic)
Underneath view
Tool in perspective to the 20 inch DeWalt 788
Front of tool--the whitish coloring on the right side is where I cut the pattern using my band saw;
Not too bad for someone with minimal fine motor skills!
Like they say in real estate, "location,location,location".
With woodworking, quality tools if used properly, make a difference. That is assuming you learn & apply from the masters--A thanks to YOU!
Not too bad for someone with minimal fine motor skills!
Like they say in real estate, "location,location,location".
With woodworking, quality tools if used properly, make a difference. That is assuming you learn & apply from the masters--A thanks to YOU!
Close-up of the "T"
The tool with the 3/8 dowel removed and centered 3/8 hole
If this helps even one person I would be happy.
You can take any & all credit--I'm just excited to begin working with my 788.
Look forward to your thoughts
Allen
If this helps even one person I would be happy.
You can take any & all credit--I'm just excited to begin working with my 788.
Look forward to your thoughts
Allen
_______________
Make sure you get your entry in for the Bear Woods $75 gift certificate giveaway. The drawing will be held early this month. I want to draw the winner before I head to Atlanta for the woodworking show.
_______________
- -
your source for Pegas scroll saw blades and craft supplies.
_______________
Look no more because Heritage Wood Specialties is
the source you have been looking for.
Let me teach you to create a beautiful wooden portrait pattern. I will show you everything you need from start to finish. The video will show you the free software program you can download for Windows or Mac OS. I will show you how to install the program and configure it for best results.
Then I will show you the technique to take your photograph and make a pattern from it. When the pattern is complete we will go in the shop and cut it.
The DVD is $10 plus shipping. This is a data DVD that you will use on your computer to watch the video tutorial
This DVD has 1,964 patterns published from 2007 thru 2016.
The DVD is $20 plus shipping. Ships to 60 countries around the world.
The DVD is $20 plus shipping. Ships to 60 countries around the world.
You can view a video showing use of the DVD on a Windows PC and a MAC at this link
Click here to Order.
Click here to Order.
My two "Wooden Vases on the Scroll Saw" books make it easy.
The books are $12 each and available for instant download after purchase. Click for Video
Demonstration.
Ad: Affiliate
Harper Trucks Lightweight 400 lb Capacity Nylon Convertible Hand Truck and Dolly
I just bought this dolly to take with me to the show in Atlanta. I'll let you know how well it works out.
- Manufactured in USA; Harper exclusive I-Beam Steel-Tough nylon truss frame is factory assembled (requires easy assembly of wheels and base plate)
- 30% lighter than steel and designed for maximum strength - frame is chemical, corrosion and rust resistant for longer life
- Converts in seconds from 2 wheel dolly to 4 wheel cart - 300 lb dolly and 400 lb cart capacity (Product images illustrates both uses, but only one cart is being sold)
- 8" wheels with solid rubber tread and 3" swivel casters
- Three position telescoping handle, built-in stair glides for easy moving up or down stairs and curbs