Friday, June 14, 2019

15" Welcome Sign Scroll Saw Pattern.



Fifteen-inch wide welcome sign. This is a large welcome sign. You will probably have to glue up a board to have the width you need. I am showing the sign with the backer board painted.

Signs like this that will be hung outside need good protection from moisture and ultraviolet light. Moisture causes rot and UV light bleaches out the natural color of the wood. The best outdoor protection is paint. If you want the natural beauty of the wood to show then you need a spar urethane finish.(Exterior Urethane)

Exterior urethanes give good protection but often need multiple coats to be effective. Even with several coats of exterior urethane, the finish will eventually cloud up. You may get three years before this start to happen. You can either accept the weathered look or add more exterior urethane to add back the gloss. 

If you paint the backer board then I would recommend adding some screws through the back to help hold the sign to the backer board. Trying to glue the sign to a painted backer board is not very secure.

If you really want the sign to last a long time you can coat the piece with epoxy sealer. After the epoxy cures, you can then give it a few coats of Exterior urethane for UV protection. That is a lot of work and expensive but if you ever need that kind of protection that is the technique that works.


Pneumatic Lift for the Seyco Scroll Saw by Paul Smith:


I have mentioned in the past that I am always watching YouTube for new scroll saw related videos. This one was posted on the 12th and I think it shows a cool idea. According to the description, Paul Smith is a 92 year young gentleman who likes to stay busy in his shop. 

Paul built a pneumatic lift system for the upper arm of his Seyco scroll saw. The system is powered by a low-PSI air system and is actuated by a button on the floor. Yes, this might be overkill for some folks but if you have strength or upper mobility problems then this could be a real help. 

I don't have any further information on this system. If you want to learn more then leave a comment in the comment section of the video and hopefully, they will read it.

Signature Coin Tip from Delvaughn Willis:


I received an email today with a handy tip. If you have purchased my Signature Coins you know that you have to drill a one-inch hole to inlay the coin. The hole depth needs to be the same as the thickness of the coin so it sets flush. It does not have to be perfect but it should be close.

I always use one of the coins to set the drill press depth stop. That works but it takes time and you have to set it up every time. Delvaughn has a simple and mostly permanent method.

He takes a fine point marker and uses one of the coins to mark the forstner bit. He sets the marker on top of the coin and turns the bit by hand marking all the way around the bit. Make sure the brad point is buried when you make the mark.

All he has to do is drill down to the line and he is ready to inlay the coin. Nice and easy. 

Thanks, Delvaughn.

$12 per sheet of 12 coins plus $3.50 shipping
Inlay with a 1" Forstner Bit.
The perfect way to sign your work.

- -

Email Newsletter Readers: Remember that the Newsletter is just a copy of the daily blog post. To see the post in it's proper formatting click this link. If you ever misplace a pattern or any item you see here you can always find it on the blog. Everything stays on the blog forever. 

Products for your consideration:


Every Scrollsaw Workshop Pattern from 2007-2018 in DVD


Purchase the entire Scrollsaw Workshop pattern catalog for offline access.

This DVD has over 2,600 patterns published from 2007 thru 2018.
The DVD is $20 plus shipping. Ships to 60 countries around the world.
If you use the DVD on a Windows PC there is a simple viewer program to browse through the patterns.

The DVD also works fine on a MAC. The viewer program is not MAC compatible but there is an included PDF with all the patterns shown as thumbnails for easy viewing.

Now Available on USB Thumb Drive

Don't have a DVD drive on your new computer. No problem. Buy the catalog on a USB thumb drive.
All the same file but on an easy to use a thumb drive. The USB thumb drive option is $23 plus shipping.


Scroll Saw Pattern Design Tutorial: DVD
Let me teach you to create a beautiful wooden portrait pattern. I will show you everything you need from start to finish. The video will show you the free software program you can download for Windows or Mac OS. I will show you how to install the program and configure it for best results. 
Then I will show you the technique to take your photograph and make a pattern from it. When the pattern is complete we will go in the shop and cut it.
The DVD is $10 plus shippingThis is a data DVD that you will use on your computer to watch the video tutorial  


Unique Wooden Vases:
Want to create beautiful wooden vases on the scroll saw?
My two "Wooden Vases on the Scroll Saw" books make it easy.

The books are $12 each and available for instant download after purchase. Click for Video Demonstration.


The Scrollsaw Workshop is primarily supported by donations. If you enjoy this Blog and would like to make a donation please click this Button. Your support is greatly appreciated. 
https://www.stevedgood.com/donate2.html

My Sponsors:
Support the businesses who support our community.
Home of Pegas scroll saw blades.