Miter Joint Clamp Scroll Saw Pattern.

If you make your own frames for scroll saw portrait patterns then this jig may be helpful.

Turn your quick clamp into a miter joint clamp. This is another simple handy shop jig that you can cut quickly on the scroll saw. There are all kinds of techniques for gluing up miter joints. This jig is pretty simple and works well.

You will need different sizes quick clamps depending on how wide the boards with the 45 are. 

Note that glue-up only miter joints are not very strong. Adding a spline or other fastener is often helpful.

These are conservative estimates.

6" clamp will glue up to 1" boards.

8" clamp will glue up to 2.5" boards

12" clamp will glue up to 5.25" boards.

If you do not have quick clamps then see the hot glue method below.

No Quick Clamp Technique:

Nail the large half of the clamp to a longer board.

Hold pressure on the clamp and the joint. Apply three blobs of hot glue. Continue to hold for a few seconds until the hot glue hardens. You will be surprised by the clamping pressure this puts on the joint. 

After the glue-up dries you can easily remove the hot glue with a chisel or scraper.

Buy on Amazon

Click to Order

$12 per sheet of 12 coins plus $3.50 shipping

Inlay with a 1" Forstner Bit.

The perfect way to sign your work.

Video Demonstration Link

- -

Email Newsletter Readers: Remember that the Newsletter is just a copy of the daily blog post. To see the post in it's proper formatting click this link. If you ever misplace a pattern or any item you see here you can always find it on the blog. Everything stays on the blog forever. 

www.scrollsawworkshop.blogspot.com

Products for your consideration:

Every Scrollsaw Workshop Pattern from 2007-2018 in DVD

Purchase the entire Scrollsaw Workshop pattern catalog for offline access.

This DVD has over 2,600 patterns published from 2007 thru 2018.
The DVD is $20 plus shipping. Ships to 60 countries around the world.

Click here to Order. 

If you use the DVD on a Windows PC there is a simple viewer program to browse through the patterns.

The DVD also works fine on a MAC. The viewer program is not MAC compatible but there is an included PDF with all the patterns shown as thumbnails for easy viewing.

Now Available on USB Thumb Drive

Don't have a DVD drive on your new computer. No problem. Buy the catalog on a USB thumb drive.
All the same file but on an easy to use a thumb drive. The USB thumb drive option is $23 plus shipping.

Buy Now. 

Scroll Saw Pattern Design Tutorial: DVD
Let me teach you to create a beautiful wooden portrait pattern. I will show you everything you need from start to finish. The video will show you the free software program you can download for Windows or Mac OS. I will show you how to install the program and configure it for best results. 

Then I will show you the technique to take your photograph and make a pattern from it. When the pattern is complete we will go in the shop and cut it.

The DVD is $10 plus shipping. This is a data DVD that you will use on your computer to watch the video tutorial  

Unique Wooden Vases:
Want to create beautiful wooden vases on the scroll saw?

My two "Wooden Vases on the Scroll Saw" books make it easy.

The books are $12 each and available for instant download after purchase. Click for Video Demonstration.

The Scrollsaw Workshop is primarily supported by donations. If you enjoy this Blog and would like to make a donation please click this Button. Your support is greatly appreciated. 

My Sponsors:

Support the businesses who support our community.

Shop Bear Woods for your craft supply needs.

Home of Pegas scroll saw blades.

Visit Heritage Wood Specialties

for you scroll saw ready boards.

Ad: Affiliate

Rockler 45 Degree Miter Sled

Just about the simplest 45-degree miter sled that is possible. 

Limited Quantity Special DealsPerfect miters - no adjustments! Simply cut one piece on the leading face, one on the trailing face, and voil! Since both pieces reference off a perfect 90 angle, the miters will fit perfectly. Pre-installed adjustable nylon pins provide a no-slop fit to the miter track.Through-slots in the base allow you to securely clamp moldings at table level.Can be easily drilled to add extended fences and stops.High-impact polycarbonate ensures durability and low-friction sliding.Fits a standard 3/8 x 3/4 miter slot.Measures 5-1/2 in width and 10-3/8 in length. Clamping faces are 7-1/2 long