Sunday, January 31, 2021

"Thy Will Be Done" Cross Scroll Saw Pattern.


 
Click to Enlarge
Download the Pattern Below
 
This three-layer plaque is eight inches wide. I wanted to keep this a simple pattern without much ornamentation. The lettering is fairly small so just take your time with that part.

Three layers of parts.


Sizing Orphaned Scroll Saw Blades:


IMPORTANT: This is not a perfect science. This chart will just get you close. Sorting scroll saw blades are not the most important job but I thought I would see if I could make it easier. Just in case you have the urge to organize.

It is easy to end up with several scroll saw blades all mixed up of different sizes. I received an email today asking how to get them sorted back to similar sizes. I had to think about it for a while but maybe this chart will help. With a brand size chart, micrometer, and magnifying glass it would be more accurate but who wants to go to all that trouble for a few cents worth of blades? For some job, close is close enough.

I have been a scroller for so long that I can identify the standard blade sizes just by touch. Maybe I'm fooling myself but I think I would get most of them correct. I have touched scroll saw blades almost every day for thirteen years. Before that was another 15 years of casual scrolling. 

If you only use a scroll saw occasionally. If you have poor sensitivity in your fingers. If you have limited vision then it may be difficult to sort them out. 

When you print out the chart pages, be certain that the print dialog is set to "Print Actual Size". If it is set to "Print to Fit" the chart will print at the incorrect size.

ALL PHOTOS CAN BE CLICKED TO ENLARGE.

We will be checking the width of the blade. 
 
I included four charts. All size blades and just standard size blades. I also included both
charts in black and red. Some low vision folks see red better. 

 
This is the #9 blade chart. A #5 blade on the #9 chart is pretty easy to see the difference.
 
This is a photo of the #5 and #7 swapped on the chart. It gets tougher but with care, you can see the difference.

The next two photos are the correct blades on the correct chart. 
 

I don't know how useful this is but I wanted to see if I could find a solution for the reader who asked the question. If you have a better, simple solution please pass it along. 


$12 per sheet of 12 coins plus $3.50 shipping
Inlay with a 1" Forstner Bit.
The perfect way to sign your work.

- -

Email Newsletter Readers: Remember that the Newsletter is just a copy of the daily blog post. To see the post in its proper formatting click this link. If you ever misplace a pattern or any item you see here you can always find it on the blog. Everything stays on the blog forever. 

Products for your consideration:

Every Scrollsaw Workshop Pattern from 2007-2020 on DVD


Purchase the entire Scrollsaw Workshop pattern catalog for offline access.

This DVD has over 3,310 patterns published from 2007 thru 2020.
The DVD is $20 plus shipping. Ships to 60 countries around the world.
If you use the DVD on a Windows PC there is a simple viewer program to browse through the patterns.

The DVD also works fine on a MAC. The viewer program is not MAC compatible but there is an included PDF with all the patterns shown as thumbnails for easy viewing.

Now Available on USB Thumb Drive

Don't have a DVD drive on your new computer. No problem. Buy the catalog on a USB thumb drive.
All the same file but in an easy to use thumb drive. The USB thumb drive option is $23 plus shipping.


Unique Wooden Vases:
Want to create beautiful wooden vases on the scroll saw?
My two "Wooden Vases on the Scroll Saw" books make it easy.

The books are $12 each and available for instant download after purchase. Click for Video Demonstration.


The Scrollsaw Workshop is primarily supported by donations. If you enjoy this Blog and would like to make a donation please click this Button. Your support is greatly appreciated. 
https://www.stevedgood.com/donate2.html

My Sponsors:
Support the businesses that support our community.
Home of Pegas scroll saw blades.


for you scroll saw ready boards.

Seyco features the Seyco ST-21 scroll saw
Make sure you check out the Seyco Scrollers Drill



Saturday, January 30, 2021

Happiness is Homemade Scroll Saw Pattern


 
Click to Enlarge
Download the Pattern Below

Patty and I both worked a lot of hours before we retired. She was a director at a local hospital and I was an on-call tech. Because of the late hours we got in the habit of eating out a lot. After we retired we still maintained that habit until the pandemic hit. We probably ate out ten plus times a week.

For the last year, we have eaten 99% of our meals at home. We both learned a very good lesson. Fast food makes us sick. Eliminating fast food almost instantly cured problems for both of us. I won't ruin your day with the details. The two or three times we have had fast food delivered in the last year did not go well. 

Now I have to admit that I still love a good Wendy's hamburger but it needs to be a treat and not a diet.
I'm sure that some of this is just us getting older but whatever it is I like feeling better more than I like Micky D's. :)

I'm not a very good cook but I am getting better. It's difficult to call what I cook homemade but it is made at home. Our diet still has a lot of flaws with too much sugar and calories but it is improving. 

Today's pattern came out of my giving thought to how we have changed our diet. It's difficult for me to say that anything positive has come from the pandemic but the food we eat is one positive for Patty and me.

Scrollsaw Blade Numbering System?


This will not be an in-depth discussion of scroll saw blades. I just want to answer a question that I have received a few times lately. There are a lot of new scroll saw folks out there right now. They got saws for Christmas and are looking for basic information.

Scroll saw blades use a numbering system to designate the size of the blade. #2/0, #1, #3, #5, #7, #9, and #12 are the more common sizes you will see. The smaller the number the smaller the blade.

The sweet spot range for most scroll saw projects is #3, #5, and #7.  This will not be true for everyone but as a general rule, these are the blades that will cut most patterns.

Blades that have fewer teeth per inch will cut more aggressively and faster. Blades with more teeth per inch will cut more accurately and slower. 

Some people will tell you to choose a blade for a project based on how thick and dense the wood you are cutting is. It is true that the #9 blade will cut 1" thick hard maple more efficiently than a #5 blade. The problem is that you may need a #5 blade to make the cut needed by the pattern. It's always a trade-off between efficiency and accuracy. I choose my blade based on the pattern and the wood.

I'm not going to discuss the different types of blades because it gets so long that everyone stops reading or falls asleep. I'll talk about the types of blades later.

If you are just getting started in the hobby, welcome. I'm happy you found my blog. If you have questions feel free to email me. I'll be honest, I am not able to answer 100% of my email but I do my best. I watch closely for people who are new and have basic questions. The first ten questions are the most important. If you get those answered your experience will be easier. I want to help you get off to a good start.

$12 per sheet of 12 coins plus $3.50 shipping
Inlay with a 1" Forstner Bit.
The perfect way to sign your work.

- -

Email Newsletter Readers: Remember that the Newsletter is just a copy of the daily blog post. To see the post in its proper formatting click this link. If you ever misplace a pattern or any item you see here you can always find it on the blog. Everything stays on the blog forever. 

Products for your consideration:

Every Scrollsaw Workshop Pattern from 2007-2020 on DVD


Purchase the entire Scrollsaw Workshop pattern catalog for offline access.

This DVD has over 3,310 patterns published from 2007 thru 2020.
The DVD is $20 plus shipping. Ships to 60 countries around the world.
If you use the DVD on a Windows PC there is a simple viewer program to browse through the patterns.

The DVD also works fine on a MAC. The viewer program is not MAC compatible but there is an included PDF with all the patterns shown as thumbnails for easy viewing.

Now Available on USB Thumb Drive

Don't have a DVD drive on your new computer. No problem. Buy the catalog on a USB thumb drive.
All the same file but in an easy to use thumb drive. The USB thumb drive option is $23 plus shipping.


Unique Wooden Vases:
Want to create beautiful wooden vases on the scroll saw?
My two "Wooden Vases on the Scroll Saw" books make it easy.

The books are $12 each and available for instant download after purchase. Click for Video Demonstration.


The Scrollsaw Workshop is primarily supported by donations. If you enjoy this Blog and would like to make a donation please click this Button. Your support is greatly appreciated. 
https://www.stevedgood.com/donate2.html

My Sponsors:
Support the businesses that support our community.
Home of Pegas scroll saw blades.


for you scroll saw ready boards.

Seyco features the Seyco ST-21 scroll saw
Make sure you check out the Seyco Scrollers Drill

 
Ad Affiliate:

Delta Power Tools 40-694 20 In. Variable Speed Scroll Saw


Still on sale for $327.79 on Amazon.


About this item

  • Electronic variable speed can be adjusted from 400-1,750 SPM for a wide array of cutting applications
  • Dual parallel link arm design reduces vibration reducing over and under cutting improving accuracy and quality
  • Upper arm lifts and locks in the raised position during blade changes or while adjusting blade position for fret work
  • Tool-free blade clamp allows for quick, easy blade changes in seconds. Bevels 0° - 45° left and right. Motor: 1.3 Amp
  • On/Off switch, electronic variable speed dial, flexible dust blower and blade-tensioning lever are all conveniently located up front on the arm for easy accessibility
  • On-tool blade storage area provides neat, organized protection for scroll saw blades, includes 2 straight blades

Friday, January 29, 2021

Cessna 172 Sign Plane Scroll Saw Pattern. Two Sizes.


 
CREATE YOUR OWN SIGN 
Click to Enlarge
Download the Pattern Below

This pattern is designed for you to make your own flying sign. There are a few premade signs in the pattern but if you make your own it will be more fun.

Support your favorite sports team, Fly your political message, Use it for a business, or just personalize it with a name.

You will need a stencil font. Here is a link to dafont that shows their stencil fonts. Just scroll down until you find one you like. Us a word processer to select the font after it is installed. You will have to play with the size. You have approximately 8.5" for the length. If you know how to use the free vector graphics program, Inkscape this will be easy. https:www.inkscape.org

The plane is cut from 1/8" and 1/4" Baltic birch plywood. The small pattern will be ~18" long.

I also included the pattern at 200%. It will make a model that is ~36" long. This model will be better for hanging from a ceiling. You can use 1/2" and 1/4" plywood for the larger pattern.
 


Back Side Tear Out of the Cut:

 
When you make a cut with a scroll saw blade there is almost always some tear-out on the backside. Sometimes this can take quite a bit of effort to sand away. Using reverse tooth blades will minimize the problem but not eliminate it.

Some plywood will tear-out worse than others. If you run into bad plywood and just can't get the back looking good then try this trick.

I always use blue painter's tape on the front of the wood. I then glue the pattern on top of the blue tape. This makes the pattern very easy to remove. Another advantage is that the glue on the tape lubricates the blade and prevents friction scorching the wood.

You can also use the tape on the back side to reduce the tear-out even more.

This is the front of the plywood. I put tape on the front for both cuts.
 
This is the back of the plywood. I only put tape on the back of one of the cuts.
 
Here is the amount of tear-out on the side with no tape on the back.
Click the image to enlarge.
 
Here is the amount of tear-out on the side that had the tape front and back.
Click the image to enlarge.

I only use this technique on rare occasions. I normally just use a mop sander you get rid of the backside fuzzies. This works but the back will almost never look as good as the front. Sometimes the plywood is just poor quality and the tear-out is really bad.

I just keep this trick in mind for the time I want the back to look as good as possible.


$12 per sheet of 12 coins plus $3.50 shipping
Inlay with a 1" Forstner Bit.
The perfect way to sign your work.

- -

Email Newsletter Readers: Remember that the Newsletter is just a copy of the daily blog post. To see the post in its proper formatting click this link. If you ever misplace a pattern or any item you see here you can always find it on the blog. Everything stays on the blog forever. 

Products for your consideration:

Every Scrollsaw Workshop Pattern from 2007-2020 on DVD


Purchase the entire Scrollsaw Workshop pattern catalog for offline access.

This DVD has over 3,310 patterns published from 2007 thru 2020.
The DVD is $20 plus shipping. Ships to 60 countries around the world.
If you use the DVD on a Windows PC there is a simple viewer program to browse through the patterns.

The DVD also works fine on a MAC. The viewer program is not MAC compatible but there is an included PDF with all the patterns shown as thumbnails for easy viewing.

Now Available on USB Thumb Drive

Don't have a DVD drive on your new computer. No problem. Buy the catalog on a USB thumb drive.
All the same file but in an easy to use thumb drive. The USB thumb drive option is $23 plus shipping.


Unique Wooden Vases:
Want to create beautiful wooden vases on the scroll saw?
My two "Wooden Vases on the Scroll Saw" books make it easy.

The books are $12 each and available for instant download after purchase. Click for Video Demonstration.


The Scrollsaw Workshop is primarily supported by donations. If you enjoy this Blog and would like to make a donation please click this Button. Your support is greatly appreciated. 
https://www.stevedgood.com/donate2.html

My Sponsors:
Support the businesses that support our community.
Home of Pegas scroll saw blades.


for you scroll saw ready boards.

Seyco features the Seyco ST-21 scroll saw
Make sure you check out the Seyco Scrollers Drill


 
Ad Affiliate

Delta Power Tools 40-694 20 In. Variable Speed Scroll Saw


Currently on sale at Amazon for $327.99


About this item

  • Electronic variable speed can be adjusted from 400-1,750 SPM for a wide array of cutting applications
  • Dual parallel link arm design reduces vibration reducing over and under cutting improving accuracy and quality
  • Upper arm lifts and locks in the raised position during blade changes or while adjusting blade position for fret work
  • Tool-free blade clamp allows for quick, easy blade changes in seconds. Bevels 0° - 45° left and right. Motor: 1.3 Amp
  • On/Off switch, electronic variable speed dial, flexible dust blower and blade-tensioning lever are all conveniently located up front on the arm for easy accessibility
  • On-tool blade storage area provides neat, organized protection for scroll saw blades, includes 2 straight blades

This is the end of the daily posts. Keep scrolling for lot's more scrolls saw fun!






https://www.bearwood.com/
Bear Woods has been around since 1987 serving our hobby. They offer a wide range of craft products including Pegas scroll saw blades, clock inserts, toy parts, workshop supplies and much more. In my ten years of writing the Scrollsaw Workshop blog I have never received a complaint about Bear Woods. I get thousands of email a month so that's saying something about their customer service and quality products. Please support the people who support our hobby. Click now and visit Bear Woods.

Heritage Wood Specialties. Scroll saw ready boards!


Heritage Wood Specialties is a nationally recognized supplier of superior quality hardwoods to fine woodworkers across the US and Canada. Novice hobbyists and experienced enthusiasts alike can enjoy the high quality woodworking materials and kits available from Heritage Wood Specialties. Great source for scroll saw ready boards.

Seyco

http://seyco.com/
Seyco began business in 1986 with the goal to supply the best customer support and quality products in the scroll saw industry. I have worked with Seyco on many occasions and I can tell you they are simply the best. Please do yourself a favor and click the image above. Steve Good

Free Pattern Catalog. 1000's of free patterns.

http://www.stevedgood.com/catalog/

Thousands of FREE scroll saw patterns. No registration or signup required.

The projects form these patterns can be sold without restrictions. The patterns cannot be sold.

Click here for the Free Online Catalog.

-

Wooden Vases on the Scroll Saw Book $12 Each

http://www.stevedgood.com/woodenvases.html
Each digital book is available for download immediately after payment.
The books are $12 per edition and contains eight unique patterns each.
Watch the following video to see how easy these beautiful scroll saw vases
are to make. 

Order the $3 pdf Catalog

This is a PDF of all the patterns in my free catalog. It is for Windows only and has a program to automatically download the pattern to your computer. Please watch the video below before you order. Click the picture to order.
http://www.stevedgood.com/swpd/swpdorderpage.html
You do not need a PayPal account to order. At the bottom of the PayPal page is a button that will allow you to pay with a credit card. After successful payment click the Return to Merchant button for the download.

Stencil Printer 1.7

Stencil Printer Instruction Video.

The Scrollsaw Workshop Stencil Printer 1.7 is my latest software for creating patterns. It will create key chain fobs, desk name plates and more. Click the image above to download the latest version. It is free to use donationware. This software is for Windows PC only.

Scroll Saw Pattern Printer update 1.1

Scroll Saw Pattern Printer update 1.1
Download the Free Scroll Saw Pattern Printer Version 1.1. Create name patterns in seconds. Windows PC only.
Download Version 1.1
Please consider a $5 donation for The Scroll Saw Pattern Printer v1.1.

Scroll Saw Keychain Pattern Maker

Use the Scroll Saw Keychain Maker to start a small keychain business. Build yourself a nice display and make up severl keychains with common names. Sell at craft shows, on Ebay or at work. Everyone needs a keychain. Take custom orders. Heck just make them and give them away as gifts. It's all made easy with the Scroll Saw Keychain Maker. Watch the video demonstration then download the file below and get started with the fun.
The following link will start the download process. After the file download is complete just click the setup file and the program will be installed. Please consider a $5 donation for the program.

Download the Oval Keychain Pattern Maker.

Enjoy designing and printing these great personalized key chains. Give them as gifts, make them for fun or sell them at craft shows. It's easy, just watch the video demo then download and install the program. You will be designing these fun projects in minutes. Windows PC only.
Download the Free Oval Key Chain Pattern Maker. Create Oval key chain patterns in seconds.
Download Version .9a
Please consider a $5 donation for The Oval Key Chain Pattern Maker.

Philip Lowndes Noah's Arc Pattern Available. Watch the video below.

This video is from Philip Lowndes. He is the designer of this beautiful Noah's Arc puzzle pattern. If you would like the pattern follow the link below.
Buy This Wonderful Heirloom Puzzle Pattern

Think Safety

Remember to keep the safety of yourself and others in your work shop in your thoughts at all times. Always wear eye and ear protection. Follow all the manufactures warnings that came with your power tools. If I demonstrate something on this web site that you don't feel is safe, don't do it. Your safety is your responsibility. Fingers are handy things, try to keep all of them.
__________________________
Disclaimer:
The Scrollsaw Workshop Blog is in no way affiliated with or sponsored by Scroll Saw Woodworking and Crafts Magazine formerly (Scroll Saw Workshop Magazine) or it's publisher Fox Chapel Publishing.

Scroll Saw Woodworking and Crafts