Organic Sculpture Scroll Saw Pattern. Love Birds.

This small organic sculpture probably won't be everyone's cup of tea. It's a little out there from a typical scroll saw pattern. I like to play with shapes. I especially like the blend of organic and architectural.  I also enjoy some abstract sculptures. My wife named it Love Birds. Okay, let's go with that. :)

My favorite abstract art uses both wood and metal. My preference for this sculpture would be for the pedestal to be cut from steel. I don't have the tools to make that happen so I used all wood.   

I think it is important to sculpt the edges of the two birds to a knife edge. If you leave them squared off it destroys the organic feel.

Request for help: Serious Geek Alert:

I am looking for some help from someone with advanced level network skills. Here is what I am trying to solve.

Network connected Laser cutter/engraver(hard wired). Set to DHCP. Ethernet cable to the router.

About 1 out of 5 times I boot the laser it will not get an IP address from the router. It will time out with its default IP address and I cannot connect to it from the desktop.

I can set a static IP address but that does not always work either.

All I have to do is reboot the Laser and it always gets an IP on the second boot. The boot time is only about three minutes but I would still like to solve the problem.

I have done quite a bit of troubleshooting already but I'm still not convinced if it is the controller in the laser not requesting the IP or the router not giving the IP.

Here is my question. Is there a way to monitor the network traffic while the laser is booting and see the request from the laser to acquire a DHCP IP address? 

I have the network packet analyzer Wireshark. The problem is that I'm not educated enough to understand the DHCP IP request packet if I see it. 

To summarize, I just am trying to figure out if the Laser control PWB is the root cause or if my router may be blocking the IP request. Can't understand why the router would only sometimes block the request. Of course, the manufacturer thinks the problem is with my network. It may be but I want proof.

Luckily this is only an inconvenience. I can always get it to work but it has become a challenge to figure out the exact cause. 

I can provide the Wireshark packet dump if that helps. 

I know I'm asking for $200 an hour help for free but it would be appreciated if you have any input.

Custom Signature Coins:

Click to Place Your Order.

$12 per sheet of 12 coins plus $3.50 shipping.

You are not billed when you place the order.

I don't send the invoice for billing until the coins are ready to ship.

You will be able to pay securely online or send a check.

More details on the order page.

Thank you for the great response to the custom signature coins. I am able to keep up with the orders daily. Most of the time the package is being shipped out the day after the order is placed. I won't promise I can get them out that fast but so far so good.

I am starting to get feedback from customers and it has been very positive overall. I even had one customer tell me he had already used all 24 of the coins he ordered. He placed a second order. He has been very busy.

I am also getting requests to put custom logo's on the coins. I am able to do that but it will be expensive for the initial setup. Keep in mind that the coins are only one inch so complex logos are not going to work very well. If you provide a good sample of the logo I will give you a quote for the setup. Make sure you are sitting down when you read the quote. Just kidding I will be as reasonable as possible. 

- -

Email Newsletter Readers: Remember that the Newsletter is just a copy of the daily blog post. To see the post in it's proper formatting click this link. If you ever misplace a pattern or any item you see here you can always find it on the blog. Everything stays on the blog forever. 

www.scrollsawworkshop.blogspot.com

Products for your consideration:

Scroll Saw Pattern Design Tutorial: DVD
Let me teach you to create a beautiful wooden portrait pattern. I will show you everything you need from start to finish. The video will show you the free software program you can download for Windows or Mac OS. I will show you how to install the program and configure it for best results. 

Then I will show you the technique to take your photograph and make a pattern from it. When the pattern is complete we will go in the shop and cut it.

The DVD is $10 plus shipping. This is a data DVD that you will use on your computer to watch the video tutorial  

Every Scrollsaw Workshop Pattern from 2007-2017 in DVD

Purchase the entire Scrollsaw Workshop pattern catalog for offline access.

This DVD has 2,300 patterns published from 2007 thru 2017.
The DVD is $20 plus shipping. Ships to 60 countries around the world.

Click here to Order. 

If you use the DVD on a Windows PC there is a simple viewer program to browse through the patterns.

The DVD also works fine on a MAC. The viewer program is not MAC compatible but there is an included PDF with all the patterns shown as thumbnails for easy viewing. 

Unique Wooden Vases:
Want to create beautiful wooden vases on the scroll saw?

My two "Wooden Vases on the Scroll Saw" books make it easy.

The books are $12 each and available for instant download after purchase. Click for Video Demonstration.

The Scrollsaw Workshop is primarily supported by donations. If you enjoy this Blog and would like to make a donation please click this Button. Your support is greatly appreciated. 

My Sponsors:

Support the businesses who support our community.

Shop Bear Woods for your craft supply needs.

Home of Pegas scroll saw blades.

Visit Heritage Wood Specialties

for you scroll saw ready boards.

Ad: Affiliate

WEN 4208 8 in. 5-Speed Drill Press

This little drill press gets very high marks on Amazon for the price. This 8-inch drill press is fine for a small scroll saw workshop. It won't handle the big jobs but it also does not cost the big bucks. Currently under $75. 

• Includes a 1/2-inch keyed chuck and onboard key storage
• Operates at 5 different speeds: 740, 1100, 1530, 2100, 3140 RPM
• Spindle travels up to 2 inches with easy to read, locking linear depth stops for accurate and repeatable drilling operations
• Durable 1/3 HP induction motor develops ample torque and power
• 6-1/2 x 6-1/2" worktable is height adjustable and bevels up to 45 degrees left & right
• Swing: 8 inch. Motor: 120V, 60Hz. Horsepower: 1/3 HP.
• Includes: Drill Press, 1/2" Keyed Chuck, Chuck Key and Tools for Assembly