Download the Pattern below
I am stuck on layered patterns right now. I'll move on to something else tomorrow. This layered doves pattern is going to be a little tricky to cut. The doves on the branch and the individual dove can be a little fragile. You will probably want to use Baltic birch plywood for the extra strength.
Dowell Drilling Tip:
I can't remember where I saw this tip but I have used it many times over the years. Occasionally I will need to drill a hole in the center of a dowel. In this case, I needed a spacer for a nut and bolt. It is a half-inch diameter wooden dowel. I needed a 1/4" bolt to go through the spacer.
You can do this by hand if you are careful but I make a quick jig to make it safer and more accurate.
Select a drill bit the same size as the dowel you will be drilling. Clamp a sacrificial board across your drill press.
Drill a hole in the board. You don't need to drill all the way through the board. Make sure the clamped board does not move from this point forward.
Install the smaller drill bit. Install the wooden dowel in the hole. You will have to play with the height of the drill press before you start to make sure you can get the large bit out without moving the table.
As long as you don't allow anything to move the smaller drill bit is now aligned with the center of the dowel. You need to hold the dowel or it will spin and create smoke. I use pliers. It is safer than trying to hold it with your fingers. If you don't want the pliers to damage the dowel then wrap them with a paper towel.
Drill the center hole slowly, lifting out the bit every 1/8" to clear the hole of shavings.
Now you should have a hole in the middle of the dowel. It won't always be perfectly centered but it is usually close enough.
$12 per sheet of 12 coins plus $3.50 shipping
Inlay with a 1" Forstner Bit.
The perfect way to sign your work.
Email Newsletter Readers: Remember that the Newsletter is just a copy of the daily blog post. To see the post in its proper formatting click this link. If you ever misplace a pattern or any item you see here you can always find it on the blog. Everything stays on the blog forever.
Products for your consideration:
Every Scrollsaw Workshop Pattern from 2007-2020 on DVD
This DVD has over 3,310 patterns published from 2007 thru 2020.
The DVD is $20 plus shipping. Ships to 60 countries around the world.
The DVD is $20 plus shipping. Ships to 60 countries around the world.
If you use the DVD on a Windows PC there is a simple viewer program to browse through the patterns.
The DVD also works fine on a MAC. The viewer program is not MAC compatible but there is an included PDF with all the patterns shown as thumbnails for easy viewing.
All the same file but in an easy to use thumb drive. The USB thumb drive option is $23 plus shipping.
Now Available on USB Thumb Drive
Don't have a DVD drive on your new computer. No problem. Buy the catalog on a USB thumb drive.All the same file but in an easy to use thumb drive. The USB thumb drive option is $23 plus shipping.
Want to create beautiful wooden vases on the scroll saw?
My two "Wooden Vases on the Scroll Saw" books make it easy.
The books are $12 each and available for instant download after purchase. Click for Video Demonstration.
My Sponsors:
Support the businesses that support our community.
Home of Pegas scroll saw blades.
for you scroll saw ready boards.
Seyco features the Seyco ST-21 scroll saw
Make sure you check out the Seyco Scrollers Drill
Make sure you check out the Seyco Scrollers Drill
WEN 4208T 2.3-Amp 8-Inch 5-Speed Benchtop Drill Press
About this item
- Features a 2.3A induction motor, an 8-inch swing, and a 2-inch spindle travel
- Includes a 1/2-inch keyed chuck and onboard key storage
- Operates at 5 different speeds: 740, 1100, 1530, 2100, or 3140 RPM
- 6.5 by 6.5 inch height adjustable worktable bevels up to 45 degrees in each direction
- Measures in at 23 inches tall with a 7 by 11-inch base
