Recipe Box Scroll Saw Pattern.

This recipe box goes with the recipe stand I published yesterday. It is designed to hold 4'X 6" recipe cards.

This box uses finger joints. I'll be honest that I would not normally do a finger joint box on the scroll saw. I have a finger joint jig that I would use. The parts would be cut out on the table saw but this is a scroll saw blog so we will use the scroll saw. 

Cutting finger joints on the scroll saw take a little finesse. You want the fingers to fit snug. I usually test cut the pattern with the wood I am using to see where I need to cut to get that sung fit. Depending on the exact thickness of the wood you may need to cut outside the pattern line to make the finger wider or inside the pattern line to make it thinner. It always best to cut it too tight and sneak up on the fit.

This will be good practice for cutting straight lines. When I am cutting a project like this I never make a turn with the scroll saw. I cut to the turn then back out and come in from the other direction to get a perfect right angle. This makes for a more accurate fitting box.

The ornamentation matches the decoration of the stand. This is optional and could be exchanged for a more personal decoration. You could add the recipient's name to the top of the box. "Grandma's Recipes". 

I kept the finger joints to a minimum. There is one on the lid and four on the box.

The box requires two small brass hinges. The need to be 3/4" wide and fit 1/4" thick wood.

Here is a link to the hinge on Bear Woods site. You can find these hinges in most craft stores.

You can also order them from Amazon

Click to Order

This is another difference when using the scroll saw to make this box. If I were using the table saw I would make the lid and box one piece. I would then use the table saw to cut the lid away from the box. When using the scroll saw you have to be careful that you get the pieces squared up when you glue the pieces together. 

Make sure you pre-drill the holes before you try to drive the brass screws. They will strip out verst easily. I also apply a little soap the the screw before I try to screw it into the wood.

The pencil holder is held in place by a friction fit. This is optional. You will also have to shorten the pencil about an inch and a half.

Click to Order

Click to Order

Click to Order

$12 per sheet of 12 coins plus $3.50 shipping

Inlay with a 1" Forstner Bit.

The perfect way to sign your work.

Video Demonstration Link

- -

Email Newsletter Readers: Remember that the Newsletter is just a copy of the daily blog post. To see the post in it's proper formatting click this link. If you ever misplace a pattern or any item you see here you can always find it on the blog. Everything stays on the blog forever. 

www.scrollsawworkshop.blogspot.com

Products for your consideration:

Scroll Saw Pattern Design Tutorial: DVD
Let me teach you to create a beautiful wooden portrait pattern. I will show you everything you need from start to finish. The video will show you the free software program you can download for Windows or Mac OS. I will show you how to install the program and configure it for best results. 

Then I will show you the technique to take your photograph and make a pattern from it. When the pattern is complete we will go in the shop and cut it.

The DVD is $10 plus shipping. This is a data DVD that you will use on your computer to watch the video tutorial  

Every Scrollsaw Workshop Pattern from 2007-2017 in DVD

Purchase the entire Scrollsaw Workshop pattern catalog for offline access.

This DVD has 2,300 patterns published from 2007 thru 2017.
The DVD is $20 plus shipping. Ships to 60 countries around the world.

Click here to Order. 

If you use the DVD on a Windows PC there is a simple viewer program to browse through the patterns.

The DVD also works fine on a MAC. The viewer program is not MAC compatible but there is an included PDF with all the patterns shown as thumbnails for easy viewing. 

Unique Wooden Vases:
Want to create beautiful wooden vases on the scroll saw?

My two "Wooden Vases on the Scroll Saw" books make it easy.

The books are $12 each and available for instant download after purchase. Click for Video Demonstration.

The Scrollsaw Workshop is primarily supported by donations. If you enjoy this Blog and would like to make a donation please click this Button. Your support is greatly appreciated. 

My Sponsors:

Support the businesses who support our community.

Shop Bear Woods for your craft supply needs.

Home of Pegas scroll saw blades.

Visit Heritage Wood Specialties

for you scroll saw ready boards.

Ad: Affiliate

Shop Fox W1851 Hybrid Cabinet Table Saw with Extension Table

• Motor: 2 HP, 110V/220V, single-phase, TEFC (Pre-Wired for 220V)
• Blade tilt: Left, 0°–45°
• Table size with extension: 27" x 55"
• Precision-ground cast-iron table and extension wings
• Dual-position (high-low) extruded-aluminum rip fence